• Register
0 votes
hola tengo un problema con un redmi note 8 2021 repare imei y patch con pandora pero lo dejo en reinicios ya le di el wipe que recomienda la herramienta pero sigue con el mismo problema ya le instalar el software pero queda igual necesito ayuda para volver hacer que encienda por lo menos
Selected model: Xiaomi M1908C3JGG (Redmi Note 8 (2021))
Operation: Patch CERT
Software version: 3.2

Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0707
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM17 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x0C4E91ED, 0x60946901, 0xD6D52C52, 0x469D68A3
Get Chip ID... [MT6768]
Get SOC ID... [FA8546254C8DBE62C069F8980498BEC8528803B9AD4FE00EA529FFC183A840E5]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [8]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68433861503E03106EB92EA711
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x90014A68433861503E03106EB92EA711
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0E8F800000 (58.24Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [B]
Read product info... OK
Product Brand : Redmi
Product Manufacturer : Xiaomi
Product Model : biloba
Product Name : biloba_global
Product Device : biloba
Product Board : biloba
Board Platform : connac1x
Build ID : SP1A.210812.016
Build Date : Tue Jan 25 01:10:35 CST 2022
Display ID : SP1A.210812.016
Security Patch : 2021-12-05
Version SDK : 31
Version Release : 12
Version Codename : REL
Firmware Version : V13.0.2.0.SCUMIXM
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Load partiton for patching... OK
Check modem patch possiblity... error, skip
Patching CERT... OK
Save patched partiton... OK
Format "parameter" partition... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.
in General questions by (160 points)

1 Answer

0 votes
Hello. Restore original backup and flash lower firmware. Then repeat operation.
by (127k points)
...