0 votes
Selected model: Mediatek Mediatek
Operation: Read Info META
Software version: 3.10

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM25 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM25 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Get sec config... OK [000000E0]
Active sec flags: []
Switch to META mode... OK
MetaCore version [10.2124.0.3]
Wait port for connecting... OK
Connecting to AP COM(49)... OK
modem_number = 1, modem_id = 1
md service = 2, ch type = 2
current modem type = Not Defined
modem img type[0] = 14
Connecting to META... OK
BB_CHIP        : MT6833
SW_TIME        : 2000.00.00
DSP_FW_VER     : 1.0
SW_VER         : TK_MD_HW
HW_VER         : Unknown
MELODY_VER     : NLWCG_MP_6833
NVSecOn ... OFF
Load DB From target... OK
NVRAM init ... OK
Read IMEI error 5

 

It fails to read imei in meta mode

 

Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): eUFS2.2_064 (01.1)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
   UFS_CID   : eUFS2.2_064
   UFS_FWVER : 01.1
   BLOCK_SIZE: 0x0000001000 (4.00Kb)
   UFS_LU0   : 0x0000400000 (4.00Mb)
   UFS_LU1   : 0x0000400000 (4.00Mb)
   UFS_LU2   : 0x0EEA400000 (59.66Gb)
RAM INFO:
   INT_SRAM: 0x0000070000 (448.00Kb)
   EXT_RAM : 0x0100000000 (4.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK [B]
Read product info... OK
Product Brand        : T-Mobile
Product Manufacturer : Wingtech
Product Model        : TMAF025G
Product Name         : Bethpage
Product Device       : Bethpage
Product Board        : S98122AA1
Board Platform       : connac1x
Build ID             : SP1A.210812.016
Build Date           : Sat Sep 24 16:35:10 CST 2022
Display ID           : TMAF025G_0.07.32
Security Patch       : 2022-09-05
Version SDK          : 31
Version Release      : 12
Version Codename     : REL
Firmware Version     : SW_S98122AA1_V060
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI:  44>82:01?9>3;0<
Repairing IMEI...
  IMEI:  861690062******
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
Selected model: Mediatek Mediatek
Operation: Repair
Software version: 3.10
And after brom imei repair now IMEI is NULL.
 

How can i fix it ?
in General questions by (300 points)

1 Answer

0 votes
Hello. Read partitions dump (except userdata and cache) and upload it.
by (198k points)
...