0 votes
It no longer connects several models and less and less can you help first I had to press volume up and down and power for them to connect now I have to leave the votes attached almost all the time and it is always disconnected below please help
Selected model: Xiaomi Redmi Note 9 (Merlin)
Operation: Read Flash Info
Software version: 4.10

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0707
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0707
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6768]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x16A5CC4D, 0xD8D29F46, 0x1324C59D, 0x0696D946
Get Chip ID... [MT6768]
Get SOC ID... [FD35A0AD129499D60585D73154C4D2710B43DDE232AAE304CFEB442FD2CCC20B]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [8]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x13014E47314A395339100366DDE2473F
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... error(1)


Selected model: Blackview BV9600 (Blackview BV9600)
Operation: Read Flash Info
Software version: 4.10

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM12 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [00000000]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0717
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Get sec config... OK [00000000]
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM12 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0717
Get sec config... OK [00000000]
Get HW & SW version from device... OK
HW VER: CA01, SW VER: 0200, HW SUB CODE: 8A00
Detect chip [MT6761]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x06D5CC32, 0xCC006E30, 0x8926FA2E, 0xAA51E4E4
Get Chip ID... [MT6761]
Get SOC ID... [BAAA76E1BD18B5172956C10ECB48A8FBD2638FEFE35EAFC3EB163EA5AF5F5C4D]
Get sec config... OK [00000000]
Load DownloadAgent... OK
Search DA... OK [5]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x150100525831424D4206D9DCD4A613A7
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... error(1)

Selected model: Xiaomi Redmi 10X 4G (Merlin)
Operation: Read Flash Info
Software version: 4.9

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E7]
Active sec flags: [SBC SLA DAA]
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x144A5A06, 0x2EC519DC, 0x6A725315, 0x27297B76
Get Chip ID... [MT6765]
Get SOC ID... [E734C7140531443DAF767CA02AAB48DCE23D29FB6FC17E98C3FC7B155ED1FE39]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x9B010059325030363400ACEE2C16298F
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... error(1)
in General questions by (120 points)

1 Answer

0 votes
Hello. Whats phone condition?
by (205k points)
normal but it doesn't let me do read info, frp any operations I have to keep the buttons pressed until it already gives send da error
Try to choose some old preloader and untick read emi.
The box opens but it doesn't connect me. Mtk doesn't give me a port when I connect a mobile phone. It's not working correctly. I've already tried several and it does the same thing. compare my box with that of a colleague on another pc and it does the same compared to another that you connect any mobile on or off and the port works correctly
if you can help me i would appreciate it
Try to change cables, try to use power adapter.
good morning, is there any possibility that you can check my box online and check that everything is fine because all my problem started from update 4.7
With what phones you have problem?
my problem is with the mtk what happens is that i connect the mobiles to the box and it does not recognize it when they are on and when they are off i have to leave the power button pressed as if the port of the box did not work it only detects them when i do that
...