0 votes

Hello, I was trying to remove LOST mode i wrongly click on format ALL FLASH now phone is DEAD . I have a same model i have read the FILE from the donor phone using optio READ PARTITONS but i uncheck USERDATA.. 

I use the scater file to flash the dead phone but still dead mode. it ocnnect USB MTK and off... How to revie the phone again? Pandora did read the BACKUP before format... I have try to write back the BACKUP but i got Error: 

[QUOTE]Get device info... OK
UFS INFO:
   UFS_CID   : MT128GAXAU2U227X
   UFS_FWVER : 0004
   BLOCK_SIZE: 0x0000001000 (4.00Kb)
   UFS_LU0   : 0x0000400000 (4.00Mb)
   UFS_LU1   : 0x0000400000 (4.00Mb)
   UFS_LU2   : 0x1DCB000000 (119.17Gb)
RAM INFO:
   INT_SRAM: 0x0000070000 (448.00Kb)
   EXT_RAM : 0x0180000000 (6.00Gb)
HEALTH:
   Pre EOL Info:  normal
   DeviceLifeTimeEstA:  0% - 10% device life time used
   DeviceLifeTimeEstB:  0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... error(0)
Read partitions info from phone... OK
Write file "efuse.bin"... OK
Write file "nvcfg.bin"... OK
Write file "nvdata.bin"... OK
Write file "nvram.bin"... OK
Write file "pgpt.bin"... OK
Write file "preloader.bin"... error(STATUS_EXCEED_AVALIABLE_RANGE)
Write file "proinfo.bin"... OK
Write file "protect1.bin"... OK
Write file "protect2.bin"... OK
Restore Backup done!

Selected model: Samsung SM-A346B (Samsung Galaxy A34 5G)
Operation: Restore From Backup
Software version: 7.9
[/QUOTE]


I have try TAR also.. but got Issue like this:

Extract scatter file... OK
Parse scatter file... OK
Load Rom Images... OK
Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM18 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0959
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0959
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Release testpoint
Advanced Bypass Security... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM18 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0959
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID =  0xE468FB35, 0x52562970, 0x7A58AFB9, 0xB224EC5A
Get Chip ID... [MT6877]
Get SOC ID... [86B6B89AC39D2F1D12AE12B7E39FF73178ABFDE13F4F4AFECCC7F4BFFA8AC86B]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [17]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): MT128GAXAU2U227X (0004)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
   UFS_CID   : MT128GAXAU2U227X
   UFS_FWVER : 0004
   BLOCK_SIZE: 0x0000001000 (4.00Kb)
   UFS_LU0   : 0x0000400000 (4.00Mb)
   UFS_LU1   : 0x0000400000 (4.00Mb)
   UFS_LU2   : 0x1DCB000000 (119.17Gb)
RAM INFO:
   INT_SRAM: 0x0000070000 (448.00Kb)
   EXT_RAM : 0x0180000000 (6.00Gb)
HEALTH:
   Pre EOL Info:  normal
   DeviceLifeTimeEstA:  0% - 10% device life time used
   DeviceLifeTimeEstB:  0% - 10% device life time used
Get scatter info... OK
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK
Read product info... error(0)
Prepare list for upgrade... OK
Checking upgrade list... error(1)
Partition "vbmeta_vendor" need for upgrade!


Selected model: Samsung SM-A346B (Samsung Galaxy A34 5G)
Operation: Write TAR
Software version: 7.9
 

 

in General questions by (120 points)

1 Answer

0 votes
Hello. Update donor phone to latest firmware and then read backup and write to dead phone.
by (207k points)
Hello,

I upgrade phone to latest U9... But how to backup what option should i choose ?

 

Read Flash partitons

Read bin

Read Region

Read OTP

 

because Read Flash partion using latest U9 i have already done... I uncheck only USERDATA... after successfull flash to dead phone it didnt help.. same situation phone keep on MTK usb detect and no detect keep on the loop..
Read partitions option.
Should i choose USERDATA also?
No.
Provide log of restore if still not solved.
Why you posting same questions in few threads? Already answered to first post.
...