Oppo a3s vibration only

0 votes
Oppo a3s Samsung emmc health bad so id did back up roms & rpmb & farmware update ffu then cleand rpmb

 

Then restor rpmb counter befor it was 418099 now it shows 8192 then i restord all the backups now phone only vibrates  need help
This is the old rpmb count
Z3X EasyJtag Software ver. 3.8.0.8

Skip loading eMMC Addon Firmware

CMD Pullup Level:2144 mV

CMD Active Level:2291 mV

Box IO Level:2600 mV

CLK Rate:36000 kHz

Bus Width:1bit,SDR

EMMC RPMB Counter: 418099

 

This is new log

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 MHz
CMD Pullup Level: 1834 mV
CMD Active Level: 1872 mV
EMMC Device Information :
EMMC CID: 150100514536334D4206900D9B8CA501
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 900D9B8C , rev. 0x06
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 10/2018
   EMMC ROM 1 (Main User Data) Capacity: 14910 MB (0003A3E00000)
   EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
   EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 8192 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_900D9B8C_20250416_011352.extcsd
EMMC Init completed.

Scanning soft partitions
GPT header is found and is valid
Partition: oppodycnvbk, [000000005000 - 000000A05000], size: 000000A00000 (10.0 MB)
Partition: oppostanvbk, [000000A05000 - 000001405000], size: 000000A00000 (10.0 MB)
Partition: modemst1, [000001405000 - 000001585000], size: 000000180000 (1.50 MB)
Partition: modemst2, [000001585000 - 000001705000], size: 000000180000 (1.50 MB)
Partition: persist, [000001705000 - 000003705000], size: 000002000000 (32.0 MB)
Partition: opporeserve1, [000003705000 - 000003F05000], size: 000000800000 (8.00 MB)
Partition: opporeserve2, [000003F05000 - 000007F05000], size: 000004000000 (64.0 MB)
Partition: reserve_exp1, [000007F05000 - 000008105000], size: 000000200000 (2.00 MB)
Partition: reserve_exp2, [000008105000 - 000008305000], size: 000000200000 (2.00 MB)
Partition: fsc, [000008305000 - 000008305400], size: 000000000400 (1.00 KB)
Partition: ssd, [000008306000 - 000008308000], size: 000000002000 (8.00 KB)
Partition: sbl1, [000008308000 - 000008388000], size: 000000080000 (512. KB)
Partition: rpm, [000008388000 - 000008408000], size: 000000080000 (512. KB)
Partition: tz, [000008408000 - 000008608000], size: 000000200000 (2.00 MB)
Partition: devcfg, [000008608000 - 000008648000], size: 000000040000 (256. KB)
Partition: sbl1bak, [000008648000 - 0000086C8000], size: 000000080000 (512. KB)
Partition: rpmbak, [0000086C8000 - 000008748000], size: 000000080000 (512. KB)
Partition: tzbak, [000008748000 - 000008948000], size: 000000200000 (2.00 MB)
Partition: devcfgbak, [000008948000 - 000008988000], size: 000000040000 (256. KB)
Partition: dsp, [000008988000 - 000009988000], size: 000001000000 (16.0 MB)
Partition: DDR, [00000A000000 - 00000A008000], size: 000000008000 (32.0 KB)
Partition: fsg, [00000A008000 - 00000A188000], size: 000000180000 (1.50 MB)
Partition: sec, [00000A188000 - 00000A18C000], size: 000000004000 (16.0 KB)
Partition: aboot, [00000A18C000 - 00000A28C000], size: 000000100000 (1.00 MB)
Partition: abootbak, [00000A28C000 - 00000A38C000], size: 000000100000 (1.00 MB)
Partition: modem, [00000A38C000 - 00001238C000], size: 000008000000 (128. MB)
Partition: dtbo, [00001238C000 - 000012B8C000], size: 000000800000 (8.00 MB)
Partition: vbmeta, [000012B8C000 - 000012B9C000], size: 000000010000 (64.0 KB)
Partition: boot, [000012B9C000 - 000016B9C000], size: 000004000000 (64.0 MB)
Partition: recovery, [000016B9C000 - 00001AB9C000], size: 000004000000 (64.0 MB)
Partition: devinfo, [00001AB9C000 - 00001AC9C000], size: 000000100000 (1.00 MB)
Partition: splash, [00001B000000 - 00001BB00000], size: 000000B00000 (11.0 MB)
Partition: LOGO, [00001BB00000 - 00001DB00000], size: 000002000000 (32.0 MB)

Partition: DRIVER, [00001DB00000 - 00001FB00000], size: 000002000000 (32.0 MB)

Partition: cache, [00001FB00000 - 00002FB00000], size: 000010000000 (256. MB)

Partition: misc, [00002FB00000 - 00002FC00000], size: 000000100000 (1.00 MB)

Partition: keystore, [00002FC00000 - 00002FC80000], size: 000000080000 (512. KB)

Partition: config, [00002FC80000 - 00002FC88000], size: 000000008000 (32.0 KB)

Partition: oem, [00002FC88000 - 00002FD88000], size: 000000100000 (1.00 MB)

Partition: limits, [000030000000 - 000030008000], size: 000000008000 (32.0 KB)

Partition: mota, [000030800000 - 000030880000], size: 000000080000 (512. KB)

Partition: dip, [000030880000 - 000030980000], size: 000000100000 (1.00 MB)

Partition: mdtp, [000030980000 - 000032980000], size: 000002000000 (32.0 MB)

Partition: syscfg, [000032980000 - 000032A00000], size: 000000080000 (512. KB)

Partition: mcfg, [000032A00000 - 000032E00000], size: 000000400000 (4.00 MB)

Partition: lksecapp, [000033000000 - 000033020000], size: 000000020000 (128. KB)

Partition: cmnlib, [000033020000 - 000033120000], size: 000000100000 (1.00 MB)

Partition: cmnlib64, [000033120000 - 000033220000], size: 000000100000 (1.00 MB)

Partition: keymaster, [000033220000 - 000033320000], size: 000000100000 (1.00 MB)

Partition: lksecappbak, [000033320000 - 000033340000], size: 000000020000 (128. KB)

Partition: cmnlibbak, [000033340000 - 000033440000], size: 000000100000 (1.00 MB)

Partition: cmnlib64bak, [000033440000 - 000033540000], size: 000000100000 (1.00 MB)

Partition: keymasterbak, [000033540000 - 000033640000], size: 000000100000 (1.00 MB)

Partition: apdp, [000033800000 - 000033840000], size: 000000040000 (256. KB)

Partition: msadp, [000033840000 - 000033880000], size: 000000040000 (256. KB)

Partition: dpo, [000033880000 - 000033882000], size: 000000002000 (8.00 KB)

Partition: logdump, [000033882000 - 000037882000], size: 000004000000 (64.0 MB)

Partition: vm-kystore, [000037882000 - 000037982000], size: 000000100000 (1.00 MB)

Partition: vm-data, [000037982000 - 000038382000], size: 000000A00000 (10.0 MB)

Partition: hyp, [000038800000 - 000039000000], size: 000000800000 (8.00 MB)

Partition: vm-system, [000039000000 - 00003D000000], size: 000004000000 (64.0 MB)

Partition: vm-linux, [00003D000000 - 00003F000000], size: 000002000000 (32.0 MB)

Partition: system, [00003F000000 - 000115900000], size: 0000D6900000 (3.35 GB)

Partition: vendor, [000115900000 - 000157860000], size: 000041F60000 (1.03 GB)

Partition: userdata, [000158000000 - 0003A3DFBE00], size: 00024BDFBE00 (9.19 GB)

GPT header successfully parsed

 

Get firmware version

 

Manufacturer = OPPO

CPU Abi = arm64-v8a

Android release = 8.1.0

Security Patch = 2021-01-05

Brand = OPPO

Device = CPH1803

Model = CPH1803

Firmware version = CPH1803EX_11_A.34

Firmware date = Fri Jan 22 14:38:34 CST 2021

This is now
in Easy JTAG by (120 points)
edited by

1 Answer

0 votes
Hello. Where are logs?
by (217k points)
See now Added the log now sir
by (120 points)
This is the old log

Setting interface to EasyJtag2/ISP_HiPower
在言
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 MHz CMD Pullup Level:1846 mv CMD Active Level: 1872 mv EMMC Device Information :
EMMC CID:150100514536334D4206900D9B8CA501
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , SN: 900D9B8C, rev, 0x06
EMMC Manufacture ID: 0x15 , OEM ID:0x00, Device Type: BGA (Discrete embedded), Date: 10/2018
EMMC ROM 1 (Main User Data) Capacty: 14910 MB(0003A3E000
EMMC ROM 23 (Boot Parttion 1/2) Capacity: 4096 KB 3(000000400000)
EMMC RPMB (Replay Protected Memory Block) Capaaty: 4096 KB (000000400000)counter:418099 , Response: not clean
EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information :
Extended CSD rev; 18 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
HW Reset Function RST_N_FUNCTION: 0x01, RST_n signal is permanently enabled
Supported partiton features PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in parttions and user data area
Device can have extended partitons attribute
Parition Settings [PARTIION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_900D9BBC_20250415_132756.extcsd EMMC Init completed.
Warning: Health report is very BAD
Device Life Time Estimaton (MLC) [269]: 0x0B Exceeded its maximum estimated device life time Device Life Time Estimation (SLC) [268]: 0x0B Exceeded its maximum estimated device life time Pre EOL information [26]:0x01 Normal
by (120 points)
edited by
Where logs of flashing, writing backups...
by (217k points)
Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 MHz
CMD Pullup Level: 1848 mV
CMD Active Level: 1871 mV
EMMC Device Information :
EMMC CID: 150100514536334D4206900D9B8CA501
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 900D9B8C , rev. 0x06
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 10/2018
   EMMC ROM 1 (Main User Data) Capacity: 14910 MB (0003A3E00000)
   EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
   EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 8192 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_900D9B8C_20250416_020213.extcsd
EMMC Init completed.

Operation: Writing all eMMC Regions...

Operation: Writing BootConfig ...
Reg: 179  Value: 0x38
Reg: 177  Value: 0x00
Reg: 162  Value: 0x01
Done

Writing to: ROM2 , start: 0x000000000000 , size: 0x000000400000
Filename: EMMC_QE63MB_ROM2_000000000000_000000400000.bin
eMMC switching to ROM2
Writing partition...
Done writing partition. Write speed: 716.65 KB/s

Writing to: ROM3 , start: 0x000000000000 , size: 0x000000400000
Filename: EMMC_QE63MB_ROM3_000000000000_000000400000.bin
eMMC switching to ROM3
Writing partition...
Done writing partition. Write speed: 713.84 KB/s

Writing to: ROM1 , start: 0x000000000000 , size: 0x000020000000
Filename: EMMC_QE63MB_ROM1_000000000000_000020000000.bin
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 4024.20 KB/s

All done   time: [00:02:24:212]
by (120 points)
Qualcomm phones required original RPMB.
by (217k points)
Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 MHz
CMD Pullup Level: 1846 mV
CMD Active Level: 1870 mV
EMMC Device Information :
EMMC CID: 150100514536334D4206900D9B8CA501
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 900D9B8C , rev. 0x06
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 10/2018
   EMMC ROM 1 (Main User Data) Capacity: 14910 MB (0003A3E00000)
   EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
   EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 8192 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_900D9B8C_20250416_021237.extcsd
EMMC Init completed.

Operation: Write by vendor (Qualcomm/HiSilicon/Omap)

Creating GPT-partitioninig
Writing PrimaryGPT at address: 000000000000
Writing BackupGPT at address: 0003A3DFBE00
GPT-partitioning done

Partition name: oppodycnvbk
Filename: oppodycnvbk_0.bin , Offset: 000000005000 , filesize: 10485760 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 3271.60 KB/s
Partition name: oppostanvbk
Filename: oppostanvbk_0.bin , Offset: 000000A05000 , filesize: 10485760 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 4043.70 KB/s
Partition name: modemst1
Filename: modemst1_0.bin , Offset: 000001405000 , filesize: 1572864 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 3874.18 KB/s
Partition name: modemst2
Filename: modemst2_0.bin , Offset: 000001585000 , filesize: 1572864 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 4086.05 KB/s
Partition name: persist
Filename: persist_0.bin , Offset: 000001705000 , filesize: 33554432 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 3992.73 KB/s
Partition name: opporeserve1
Filename: opporeserve1_0.bin , Offset: 000003705000 , filesize: 8388608 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 4078.51 KB/s
Partition name: opporeserve2
Filename: opporeserve2_0.bin , Offset: 000003F05000 , filesize: 67108864 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 4052.19 KB/s
Partition name: fsc
Filename: fsc_0.bin , Offset: 000008305000 , filesize: 1024 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 37.29 KB/s
Partition name: fsg
Filename: fsg_0.bin , Offset: 00000A008000 , filesize: 1572864 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 4079.28 KB/s
Partition name: sec
Filename: sec_0.bin , Offset: 00000A188000 , filesize: 16384 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 865.80 KB/s
Partition name: modem
Filename: modem_0.bin , Offset: 00000A38C000 , filesize: 134217728 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 4064.93 KB/s
Partition name: devinfo
Filename: devinfo_0.bin , Offset: 00001AB9C000 , filesize: 1048576 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 3776.61 KB/s
Partition name: keystore
Filename: keystore_0.bin , Offset: 00002FC00000 , filesize: 524288 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 4002.80 KB/s

Partition name: config
Filename: config_0.bin , Offset: 00002FC80000 , filesize: 32768 bytes
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 2833.61 KB/s

All done   time: [00:01:09:462]
by (120 points)
Yes bro i used the original rpmb backup file
by (120 points)
Where did you write it?
by (217k points)

Running:SAMSUNG: MoviNAND Reset + Format...
Z3X EasyJtag Software ver. 3.8.0.7
Skip loading eMMC Addon Firmware
CMD Pullup Level:1895 mV
CMD Active Level:1875 mV
Box IO Level:1800 mV
CLK Rate:14000 kHz
EMMC ROM2/3 (Boot Partitions) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
Sending Internal Reconfiguration Request...
Waiting configuration Apply!
Restoring configuration...
EMMC ROM2/3 (Boot Partitions) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
Wiping Card... Please do not touch it!
Please don't forget to repair extCSD from backup!
Done.
Running:SAMSUNG: eMMC firmware update...
Chip Init OK...
Downloading FFU:C:\Users\Heros King Silve\Desktop\a3s 2\eMMC_Firmware_KMQE60013M-B31816GB@BGA221Rev1.bin
Checking security ...
Z3X EasyJtag Software ver. 3.8.0.7
Checking firmware type...
OK;
Skip loading eMMC Addon Firmware
Box S/N: 3A41EC1A9F20E657, ,FW Ver.: 02.53
CMD Pullup Level:1896 mV
CMD Active Level:1875 mV
Box IO Level:1800 mV
CLK Rate:14000 kHz
Using firmware file : C:\Users\Heros King Silve\Desktop\a3s 2\eMMC_Firmware_KMQE60013M-B31816GB@BGA221Rev1.bin
Update Firmware ID Hash:
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
eMMC CID : 150100514536334D300914009B8CA5A1

Repairing eMMC CID...
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D

Repairing eMMC CSD...
Success!
eMMC firmware is updated now!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.
Checking security ...
Running:RPMB: Program KEY
Z3X EasyJtag Software ver. 3.8.0.7
Skip loading eMMC Addon Firmware
CMD Pullup Level:1883 mV
CMD Active Level:1875 mV
Box IO Level:1800 mV
CLK Rate:24000 kHz
Bus Width:1bit,SDR
Check OK Programming KEY...
RPMB Key program success!
Processing file...D:\EMMC_RPMB_QE63MB_2416810892_00000000_00400000.bin
Checking security ...
Z3X EasyJtag Software ver. 3.8.0.7
Skip loading eMMC Addon Firmware
CMD Pullup Level:1896 mV
CMD Active Level:1873 mV
Input file : D:\EMMC_RPMB_QE63MB_2416810892_00000000_00400000.bin
Writing RPMB Area...
Done, time taken: 301 sec. Average Write Speed: 13 kB/s

by (120 points)
Full rpmb clean & restor log
by (120 points)

Copyright © 2025 z3x-team Q&A - All rights reserved.

Powered by Question2Answer

Theme Designed By: Q2A Market

...