Sir. I downgraded with the firmware but same phone Stuck on Bootloop Please Help
Selected model: OPPO CPH2339 (Oppo A77 5G)
Operation: Repair
Software version: 6.10
Work ID: 30446269
Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V2023,usb2ser_mtk.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA3AAF1D2, 0x5F173115, 0x49395394, 0xDC996C43
Get Chip ID... [MT6833]
Get SOC ID... [2DE2B23E151212BA326C7C9CEE09F8F42DA1624D017B6FF13C80C8460ED49975]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM2L9001CM-B518 (0700)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM2L9001CM-B518
UFS_FWVER : 0700
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : OPPO
Product Manufacturer : OPPO
Product Model : CPH2339
Product Name : CPH2339
Product Device : OP52F3L1
Product Board : k6833v1_64
Board Platform : mt6833
Build ID : SP1A.210812.016
Build Date : Sat May 7 00:02:14 CST 2022
Display ID : CPH2339_11_A.03
Security Patch : 2022-04-05
Version SDK : 31
Version Release : 12
Version Codename : REL
Firmware Version : S.202205070027
Userdata FS Type : F2FS
Read security partition from phone...
Decrypting security data... OK
Encrypt security data... OK
Read partition "nvdata"... OK
Read partition "protect1"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read security files... OK
Calculating... OK
Repairing IMEI...
IMEI 1: 866034051708586
IMEI 2: 866034051708594
Write IMEI and patch CERT [NVDATA]... OK
Checking patch type... [1]
Patching CERT... OK
Save patched partiton... OK
Updating NVRAM... OK
Selected "Disable VBMETA verification"
Read security partition from phone... OK
Write security partition to phone... OK
Write IMEI and patch CERT [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security and Patch cert done!
If your phone after repair keeps rebooting - use wipe data option.
Selected model: OPPO CPH2339 (Oppo A77 5G)
Operation: Wipe Data
Software version: 6.10
There is a risk of data loss.
This procedure will erase all User Data
Make sure that you have a backup created. Continue? YES
Work ID: 30446651
Connect phone in BROM Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V2023,usb2ser_mtk.sys,3.0.1512.0]
You are using driver version 3.0.1512.0, we recommend using version 3.0.1504.0 for proper operation. You can install the correct driver from the program directory.
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0989
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6833]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xA3AAF1D2, 0x5F173115, 0x49395394, 0xDC996C43
Get Chip ID... [MT6833]
Get SOC ID... [2DE2B23E151212BA326C7C9CEE09F8F42DA1624D017B6FF13C80C8460ED49975]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [14]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM2L9001CM-B518 (0700)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM2L9001CM-B518
UFS_FWVER : 0700
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448.00Kb)
EXT_RAM : 0x0100000000 (4.00Gb)
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EROFS] ... OK
Product Brand : OPPO
Product Manufacturer : OPPO
Product Model : CPH2339
Product Name : CPH2339
Product Device : OP52F3L1
Product Board : k6833v1_64
Board Platform : mt6833
Build ID : SP1A.210812.016
Build Date : Sat May 7 00:02:14 CST 2022
Display ID : CPH2339_11_A.03
Security Patch : 2022-04-05
Version SDK : 31
Version Release : 12
Version Codename : REL
Firmware Version : S.202205070027
Userdata FS Type : F2FS
Formatting "userdata" partition... OK
Formatting "metadata" partition... OK
Wipe data done!